Physics 0625/32 May/June 2020: question paper and mark scheme
Cambridge IGCSE Physics (0625), Paper 3 Core Theory, May/June 2020. Read both free below, or download them. Done the paper? Get it marked by AI against this mark scheme.
Some students observe drops of water falling from a tap that leaks, as shown in Fig. 1.1.
Fig. 1.1
(a) The students measure the time for 50 drops to fall from the tap. The time for 50 drops to fall is
20 s.
Calculate the average time between two drops falling.
average time = …… s [2]
(b) The students collect some drops of water.
(i) The students measure the volume of the water they collect.
State the term for the equipment that is suitable for measuring the volume accurately.
…… [1]
(ii) In a similar experiment, another student collects 0.21 kg of water.
Calculate the weight of this water.
weight of water = …… N [3]
[Total: 6]
(a) Some students determine the speed of a car on a road. The students measure the time for the car to travel 30 m along the road. The time is 5.4 s.
Calculate the average speed of the car.
average speed = …… m / s [3]
(b) Another car moves at a constant speed of 16 m / s for 4.0 seconds. During the next 2.0 seconds, the car decelerates from a speed of 16 m / s to a speed of 13 m / s. It then continues at a constant speed of 13 m / s for 3.0 seconds.
On Fig. 2.1, plot the speed–time graph for the motion of the car during these 9.0 s.
20 speed m/s
15
10
5
0
0 2.0 4.0 6.0 8.0 10.0
time / s
Fig. 2.1
[3]
(c) A motorcycle accelerates as shown in Fig. 2.2. Calculate the distance the motorcycle travels while it is accelerating. Use information from Fig. 2.2.
40 speed m/s
30
20
10
0
0 1.0 2.0 3.0 4.0 5.0 time / s
Fig. 2.2
distance travelled = …… m [3]
[Total: 9]
Mark scheme
2(a) (s =) d ÷ t OR s = d ÷ t in any form C1
(average speed =) 30 ÷ 5.4 C1
5.6 (m / s) A1
2(b)(i) first section and third section horizontal straight lines B1
second section line with negative gradient B1
first section horizontal line at 16 m / s AND third section horizontal line at 13 m / s at correct times B1
2(b)(ii) 1 C1
(d =) × (a + b) × t OR area under graph
2
1 1 C1
× (24 + 30) × 2.5 OR (24 × 2.5) + ( × 6 × 2.5)
2 2
67.5 (m) A1
Fig. 3.1 shows an archer pulling the string of a bow.
string arrow
fingers on string hand pushing bow
archer bow
Fig. 3.1
(a) The archer uses a force of 120 N. The force acts on an area of 0.5 cm2 on the archer’s fingers.
Calculate the pressure on the archer’s fingers.
pressure on fingers = …… N / cm2 [3]
(b) The archer’s other hand is pushing the bow with the same force of 120 N. This force acts on a larger area than the force in (a).
State whether the pressure on this hand is greater than, the same as or less than the pressure on the fingers holding the string.
…… [1]
(c) State the type of energy stored in the bow when the archer bends it as shown in Fig. 3.1.
…… [1]
[Total: 5]
Mark scheme
3(a) P = F ÷ A in any form C1
120 ÷ 0.5 C1
240 (N / cm2) A1
3(b) Less (than) B1
3(c) elastic OR strain OR potential B1
(a) Match each description with the correct state of matter in Table 4.1.
Write the correct letter in Table 4.1.
A – Molecules move around freely and are far apart from each other.
B – Molecules vibrate about fixed positions.
C – Molecules move around randomly and are close to each other.
Table 4.1
state of matter description
solids
liquids
gases
[2]
(b) Some students heat water in a beaker. They measure the temperature every minute. They heat the water for 8 minutes until it boils, and then continue to heat it for a further 5 minutes.
Describe and explain how the temperature of the water changes during the 13 minutes.
…… [3]
[Total: 5]
Mark scheme
4(a) B B2
C
A
4(b) any three from: B3
during first eight minutes temp rises
(because) internal energy of water rises (from thermal energy input)
during next five minutes temperature is constant / stays the same
(because) internal energy does not rise (at boiling point)
Fig. 5.1 shows a ray of red light passing through a semicircular glass block.
air ray of red light
q p r s
semicircular glass block
Fig. 5.1
(a) (i) State the term for the dotted line shown in Fig. 5.1.
…… [1]
(ii) State which angle p, q, r or s is the angle of incidence for the ray of red light.
…… [1]
(iii) State which angle p, q, r or s is the angle of refraction.
…… [1]
(iv) State what happens to the speed of the red light as it enters the semicircular glass block from the air.
…… [1]
(b) Fig. 5.2 shows the path of a ray of light entering a semicircular glass block. The critical angle for the glass block is 42°.
On Fig. 5.2, continue the path of the ray. Show clearly its direction on leaving the glass block.
ray of light
62°
semicircular glass block
Fig. 5.2
[2]
(c) A ray of white light passes through two prisms as shown in Fig. 5.3.
prisms
D
E
F
ray of white light
Fig. 5.3
Draw one line to link the letter for each position to the correct effect at that position.
position effect
(i)
refraction
D diffraction
total internal reflection
[1]
(ii)
reflection
E dispersion
diffraction
[1]
(iii) red, green and blue light only produced
F white light produced
spectrum of visible light produced
[1]
[Total: 9]
Mark scheme
5(a)(i) normal B1
5(a)(ii) p B1
5(a)(iii) r B1
5(a)(iv) speed decreases B1
5(b) reflects off flat surface at same angle (by eye) B1
passes through curved surface without deviation B1
5(c)(i) D – total internal reflection B1
5(c)(ii) E – dispersion B1
5(c)(iii) F – spectrum of visible light B1
Fig. 6.1 shows a hot liquid in a vacuum flask. The vacuum flask keeps the temperature of the liquid in the flask constant for a long time.
stopper
hot liquid shiny silver surface
vacuum (space without particles) shiny silver surface
Fig. 6.1
(a) Describe how each feature helps to keep the liquid hot for longer.
(i) shiny silver surface
…… [2]
(ii) the vacuum between the silvered surfaces
…… [3]
(b) (i) Suggest a material for the stopper that will help to keep the liquid hot for longer.
material …… [1]
(ii) Give a reason for your answer.
reason ……
…… [1]
[Total: 7]
Mark scheme
6(a)(i) reflects / does not allow transmission of B1
infrared / thermal radiation B1
6(a)(ii) heat loss by conduction cannot take place B1
heat loss by convection cannot take place B1
because particles are needed for conduction and / or convection B1
6(b)(i) non-metal B1
6(b)(ii) metals are good conductors of heat / non-metals are good insulators / poor conductors B1
Fig. 7.1 shows a diagram of the main regions of the electromagnetic spectrum. Two labels are missing.
γ-rays
X-rays
ultraviolet
infrared
radio
Fig. 7.1
(a) (i) Complete the labels on Fig. 7.1. [2]
(ii) State two properties that are the same for all waves in the electromagnetic spectrum.
1. ……
2. ……
[2]
(b) State which region of the electromagnetic spectrum is used in each situation.
(i) detecting objects without opening baggage at a security check
…… [1]
(ii) television remote control
…… [1]
(iii) satellite television transmissions
…… [1]
[Total: 7]
Mark scheme
7(a)(i) top – visible light B1
bottom – microwaves B1
7(a)(ii) any two from: B2
transverse wave
travel at same speed
do not need a medium
7(b)(i) X-rays B1
7(b)(ii) infrared B1
7(b)(iii) microwaves B1
Sound travels as a wave.
(a) Complete each sentence.
Sound is produced when an object …… .
An echo is produced when sound is …… from a hard surface.
Compared with a quiet sound, a loud sound always has a greater …… .
Compared with a high pitched sound, a low pitched sound always has a smaller …… .
Waves transfer energy without transferring …… .
[5]
(b) State the meaning of the term ultrasound.
…… [1]
[Total: 6]
Mark scheme
8(a) vibrates B1
reflected B1
amplitude B1
frequency B1
matter B1
8(b) vibrations with higher frequency than sound B1
Some students plot the magnetic field lines around a bar magnet. They have the apparatus shown in Fig. 9.1 and a large sheet of paper.
bar magnet plotting compass pencil
Fig. 9.1
(a) Describe how the students use the apparatus in Fig. 9.1 to show the pattern of the magnetic field lines around the bar magnet.
You may draw a diagram to assist with your description.
…… [3]
(b) Draw at least four lines above and below the bar magnet in Fig. 9.2 to show the magnetic field around the bar magnet. Draw an arrow on the field lines to show the direction of the magnetic field.
N S
Fig. 9.2
[3]
[Total: 6]
Mark scheme
9(a) any three from: B3
use of plotting compass next to magnet
mark point of compass needle
move compass other side of dot
align needle with dot put dot other side of needle and repeat
start again from another position next to magnet
9(b) any two from: B2
no field lines crossing
looping from N to S away from ends
field lines straight out from ends
arrow(s) on field lines pointing N to S B1
A student connects three identical lamps J, K and L in a circuit, as shown in Fig. 10.1.
Switch S1 is open and the current in ammeter A1 = 0.2 A.
A1
K
A2
J
A3
L S1
Fig. 10.1
Use words from the box to complete the sentences.
Each word may be used once, more than once, or not at all.
the same increased decreased
(a) The switch S1 in Fig. 10.1 is closed. State and explain the effect on the circuit.
(i) The current in ammeter A1 is …… because the resistance of the whole
circuit is …… . [2]
(ii) The current in ammeter A2 is …… . [1]
(b) A student measures the potential difference (p.d.) across lamp J by using a voltmeter.
On Fig. 10.1, draw the correct electrical symbol for the voltmeter with the correct connections.
[2]
(c) The p.d. across lamp J is 3.0 V and the current shown by ammeter A3 is 0.15 A.
Calculate the resistance of lamp J. Include the unit in your answer.
resistance of lamp J = …… unit…… [4]
[Total: 9]
Mark scheme
10(a)(i) increased B1
decreased B1
10(a)(ii) the same B1
10(b) correct voltmeter symbol B1
in parallel with battery B1
10(c) R = V ÷ I in any form C1
3(.0) ÷ 0.15 C1
20 A1
Ω / ohms B1
A model train uses an electric motor. The motor has a coil of wire in a magnetic field.
(a) Fig. 11.1 shows a coil of wire in a magnetic field.
north pole south pole
N
S current
coil of wire
Fig. 11.1
Describe two ways of increasing the turning effect on the coil.
…… [2]
(b) The motor for the model train uses an alternating voltage of 12 V. This is supplied by the secondary coil of a transformer.
The primary coil of the transformer is connected to a mains voltage of 240 V.
The primary coil has 900 turns.
Calculate the number of turns on the secondary coil.
number of turns on the secondary coil = …… [3]
[Total: 5]
Mark scheme
11(a) any two from: B2
increase current
increase magnetic field strength field
more turns on coil
11(b) (Vp / Vs) = (Np / Ns) in any form C1
Ns = (12 ÷ 240) × 900 C1
45 A1
(a) Carbon-14 is a radioactive isotope of carbon. An atom of carbon-14 has 6 protons in its nucleus.
Another isotope of carbon is carbon-12.
(i) Determine the number of protons in a carbon-12 nucleus.
…… [1]
(ii) Determine the number of neutrons in a carbon-14 nucleus.
…… [1]
(iii) Determine the number of electrons orbiting the nucleus of a single carbon-14 atom.
…… [1]
(b) Carbon-14 decays by emitting a β-particle.
State what happens to a nucleus of carbon-14 when it emits a β-particle.
…… [1]
(c) People working with radioactive sources need to take safety precautions.
(i) A shielding material can absorb ionising radiation and reduce the damage to living tissue.
State a suitable material that will absorb all types of naturally occurring nuclear radiation.
…… [1]
(ii) Apart from using shielding, state how a person can reduce the amount of ionising radiation they absorb when they handle samples of radioactive substances.
…… [1]
[Total: 6]
Mark scheme
12(a)(i) 6 B1
12(a)(ii) 8 B1
12(a)(iii) 6 B1
12(b) changes to a different element / gains a proton B1
12(c)(i) lead B1
12(c)(ii) any one from: B1
minimise time for handling
maximise distance from source
use of shielding
prevent contamination
Checked your answers against these? Let AI mark the whole paper, on your own working.
Examiners follow the generic marking principles at the front of the scheme, then each question's points: method (M), accuracy (A) and independent (B) marks, error carried forward where the scheme allows it, and positive marking, so you're credited for what you got right.
Check your answers against it
Done this paper? Upload your script and CIE Buddy's AI marker marks it question by question against this exact scheme, puts the ticks on your own working and says what each lost mark needed.
Where can I find the 0625/32 May/June 2020 mark scheme?+
On this page, free: the mark scheme for IGCSE Physics 0625/32, May/June 2020 (0625_s20_ms_32), and the question paper (0625_s20_qp_32), to read or download, with each question's marking points written out underneath.
How many marks is 0625/32 out of?+
Physics 0625/32 for May/June 2020 is out of 80 marks, with 1 hour 15 minutes to answer it, across 12 questions.
Can I get my 0625/32 answers marked?+
Yes. Upload your answers to 0625/32/M/J/20 as a PDF or photos, and CIE Buddy marks every question against this paper's official mark scheme, using Cambridge's marking rules. You get your score, each lost mark explained on your own script, and the topics to revise. It's a guide, not an official Cambridge grade.